Skip to content
Sunday, November 22, 2026

Community Q&A

All questions

Search shop questions the way people find them — by answers, topic, and what was asked next.

84 questions

Power & Piston · CFM and air 1 answer · 2 years ago

What PSI should I run to clean weld scale on structural beams without warping thin metal in a small shop?

Thin structural beams panels warp when I blast hard. Media is silicon carbide, nozzle is #4 (1/4"). Need a safer pressure window for coating with zinc-rich primer. Looking for guidance that matches…

Top answer: On thin structural beams, begin near the low end of 80 PSI and increase only until you clean weld scale cleanly. Hot spots and long dwell times warp…

More results from powerandpiston.com

Power & Piston · CFM and air 1 answer · 2 years ago

Why does my blast pressure drop below 80 PSI after a few minutes in a small shop (guide 494)?

Pot holds pressure at rest, then falls once I pull the trigger on welded fabrications. Setup uses a #4 (1/4") nozzle and a compressor advertised at 50 CFM. Looking for guidance that…

Top answer: Pressure collapse after a few minutes usually means the compressor cannot sustain the nozzle demand. A #4 (1/4") at working pressure often exceeds a 50 CFM intermittent rating.Check…

More results from powerandpiston.com

Power & Piston · CFM and air 1 answer · 2 years ago

How much CFM do I need for a #4 (1/4″) nozzle at 80 PSI in a small shop (guide 488)?

Planning air for a contractor pot. Target pressure is 80 PSI with a #4 (1/4") nozzle while I prep for powder coat on farm equipment. Current compressor is rated near 100 CFM.…

Top answer: A #4 (1/4") nozzle at 80 PSI typically needs more continuous CFM than intermittent tool ratings suggest. Treat 100 CFM as a starting estimate and size for duty…

More results from powerandpiston.com

Power & Piston · CFM and air 1 answer · 2 years ago

What PSI should I run to strip paint on stainless steel without warping thin metal in a small shop?

Thin stainless steel panels warp when I blast hard. Media is aluminum oxide, nozzle is #4 (1/4"). Need a safer pressure window for coating with powder coat. Looking for guidance that matches…

Top answer: On thin stainless steel, begin near the low end of 80 PSI and increase only until you strip paint cleanly. Hot spots and long dwell times warp panels…

More results from powerandpiston.com

Power & Piston · CFM and air 1 answer · 2 years ago

Why does my blast pressure drop below 80 PSI after a few minutes in a small shop (guide 476)?

Pot holds pressure at rest, then falls once I pull the trigger on alloy wheels. Setup uses a #4 (1/4") nozzle and a compressor advertised at 25 CFM. Looking for guidance that…

Top answer: Pressure collapse after a few minutes usually means the compressor cannot sustain the nozzle demand. A #4 (1/4") at working pressure often exceeds a 25 CFM intermittent rating.Check…

More results from powerandpiston.com

Power & Piston · CFM and air 1 answer · 2 years ago

How much CFM do I need for a #4 (1/4″) nozzle at 80 PSI in a small shop (guide 470)?

Planning air for a vacuum blast unit. Target pressure is 80 PSI with a #4 (1/4") nozzle while I peen for fatigue life on steel tanks. Current compressor is rated near 50…

Top answer: A #4 (1/4") nozzle at 80 PSI typically needs more continuous CFM than intermittent tool ratings suggest. Treat 50 CFM as a starting estimate and size for duty…

More results from powerandpiston.com

Power & Piston · CFM and air 1 answer · 2 years ago

What PSI should I run to prep for powder coat on cast iron without warping thin metal in a small shop?

Thin cast iron panels warp when I blast hard. Media is silicon carbide, nozzle is #4 (1/4"). Need a safer pressure window for coating with clear coat. Looking for guidance that matches…

Top answer: On thin cast iron, begin near the low end of 80 PSI and increase only until you prep for powder coat cleanly. Hot spots and long dwell times…

More results from powerandpiston.com

Power & Piston · CFM and air 1 answer · 2 years ago

Why does my blast pressure drop below 80 PSI after a few minutes in a small shop (guide 458)?

Pot holds pressure at rest, then falls once I pull the trigger on exhaust manifolds. Setup uses a #4 (1/4") nozzle and a compressor advertised at 15 CFM. Looking for guidance that…

Top answer: Pressure collapse after a few minutes usually means the compressor cannot sustain the nozzle demand. A #4 (1/4") at working pressure often exceeds a 15 CFM intermittent rating.Check…

More results from powerandpiston.com

Power & Piston · CFM and air 1 answer · 2 years ago

How much CFM do I need for a #4 (1/4″) nozzle at 80 PSI in a small shop (guide 452)?

Planning air for a blast room. Target pressure is 80 PSI with a #4 (1/4") nozzle while I clean weld scale on sheet metal panels. Current compressor is rated near 25 CFM.…

Top answer: A #4 (1/4") nozzle at 80 PSI typically needs more continuous CFM than intermittent tool ratings suggest. Treat 25 CFM as a starting estimate and size for duty…

More results from powerandpiston.com

Power & Piston · CFM and air 1 answer · 2 years ago

What PSI should I run to peen for fatigue life on automotive frames without warping thin metal in a small shop?

Thin automotive frames panels warp when I blast hard. Media is aluminum oxide, nozzle is #4 (1/4"). Need a safer pressure window for coating with paint strip. Looking for guidance that matches…

Top answer: On thin automotive frames, begin near the low end of 80 PSI and increase only until you peen for fatigue life cleanly. Hot spots and long dwell times…

More results from powerandpiston.com

Post