Skip to content
Sunday, November 22, 2026

Browse shop questions or ask your own. Practical answers on blasting media, air, and equipment.

Admin 19 Mar · asked in Machines
Answered

Why does my dual-chamber cabinet keep clogging when I use garnet in a small shop (guide 351)?

Frequent stoppages while blasting wrought iron. Media is garnet, moisture is sometimes visible in the line, pressure target 90 PSI.

Machines

Top answer

Clogs with garnet almost always trace to moisture, fines, or an orifice mismatch. Dry the air, screen the media, and verify the metering valve is set for that…

0 found this helpful 2 answers
Answer
Admin 16 Jan · asked in Blast media
Answered

What plastic media grit works best to restore castings on brake drums?

I am blasting brake drums to restore castings. Shop runs about 60 PSI with a #3 (3/16") nozzle. Looking for a practical plastic media starting point that will…

Blast media

Top answer

For brake drums, start with plastic media around 80 grit when your goal is to restore castings. At roughly 60 PSI, a #3 (3/16") nozzle gives a controllable…

0 found this helpful 2 answers
Answer
Sumer Choudhary 7 Oct · asked in Blast media
Answered

How do you select the right abrasive media for a particular material?

How to Select the Right Abrasive Media for a Material Select abrasive media based on the workpiece material, hardness, required material removal, desired surface finish, and the operation.…

Blast media

Top answer

Choosing the right abrasive media depends mainly on the material being blasted, the type of contamination, and the required surface finish. For example, steel shot or steel grit…

1 found this helpful 1 answer
Answer
Jai Pal 6 Oct · asked in Media
Answered

How to choose a sand blasting machine?

Don't ignore this category. Safety is an important part of abrasive-blasting content because dust, noise, eye/skin injury and respiratory exposure are recognized hazards.

Media

Top answer

First define the job → select abrasive → select nozzle → calculate air requirement → choose machine size → select dust collection and recovery system. For example, if…

0 found this helpful 1 answer
Answer
Admin 19 Apr · asked in CFM and air
Answered

What PSI should I run to clean weld scale on structural beams without warping thin metal in a small shop?

Thin structural beams panels warp when I blast hard. Media is silicon carbide, nozzle is #4 (1/4"). Need a safer pressure window for coating with zinc-rich primer. Looking…

CFM and air

Top answer

On thin structural beams, begin near the low end of 80 PSI and increase only until you clean weld scale cleanly. Hot spots and long dwell times warp…

0 found this helpful 1 answer
Answer
Admin 19 Apr · asked in Blast media
Answered

How many times can I reclaim plastic media when blasting gate hardware in a small shop (guide 499)?

Running a reclaim setup on a portable blaster. Media is plastic media for create a paint-ready profile. Wondering when cutting power drops too far for reliable prep. Looking…

Blast media

Top answer

Reclaim plastic media while particle edges still cut. For gate hardware work aimed at create a paint-ready profile, expect useful life of several cycles if you keep dust…

0 found this helpful 1 answer
Answer
Admin 19 Apr · asked in Shop floor
Answered

What is the most common mistake when learning to strip paint in a small shop (guide 498)?

Training new operators on exhaust manifolds. Equipment is a pressure blast pot, media walnut shell. Want a short checklist that prevents rework before powder coat. Looking for guidance…

Shop floor

Top answer

The most common mistake is dwelling too long in one spot at high pressure. That dishes soft exhaust manifolds areas and creates an uneven profile for powder coat.Second…

0 found this helpful 1 answer
Answer
Admin 18 Apr · asked in Safety
Answered

Is it safe to sandblast in a garage with only a safety glasses in a small shop (guide 496)?

Hobby blasting on alloy wheels parts. Media is steel grit. Garage has a door fan but no dedicated dust booth. Sessions last about 4 hours. Looking for guidance…

Safety

Top answer

A garage fan plus a safety glasses is not enough for repeated steel grit blasting. Fine dust settles on tools, cars, and lungs long after the visible cloud…

0 found this helpful 1 answer
Answer
Admin 18 Apr · asked in Machines
Answered

Why does my dual-chamber cabinet keep clogging when I use garnet in a small shop (guide 495)?

Frequent stoppages while blasting brake drums. Media is garnet, moisture is sometimes visible in the line, pressure target 90 PSI. Looking for guidance that matches Google-friendly, clear how-to…

Machines

Top answer

Clogs with garnet almost always trace to moisture, fines, or an orifice mismatch. Dry the air, screen the media, and verify the metering valve is set for that…

0 found this helpful 1 answer
Answer
Admin 18 Apr · asked in CFM and air
Answered

Why does my blast pressure drop below 80 PSI after a few minutes in a small shop (guide 494)?

Pot holds pressure at rest, then falls once I pull the trigger on welded fabrications. Setup uses a #4 (1/4") nozzle and a compressor advertised at 50 CFM.…

CFM and air

Top answer

Pressure collapse after a few minutes usually means the compressor cannot sustain the nozzle demand. A #4 (1/4") at working pressure often exceeds a 50 CFM intermittent rating.Check…

0 found this helpful 1 answer
Answer
Admin 18 Apr · asked in Blast media
Answered

Is glass bead better than garnet for cleaning heavy plate before galvanizing prep in a small shop?

Comparing abrasives for heavy plate prep ahead of galvanizing prep. Compressor delivers about 35 CFM. Want a finish that accepts primer without heavy sanding. Looking for guidance that…

Blast media

Top answer

Glass Bead and garnet can both prep heavy plate, but they leave different profiles. Glass Bead at about 16 grit is a solid first choice when you need…

0 found this helpful 1 answer
Answer
Admin 17 Apr · asked in Shop floor
Answered

How long does it take to clean weld scale on a typical sheet metal panels part in a small shop?

Estimating labor for shop quoting. Setup is a blast room with copper slag at 120 PSI. Parts vary but are mostly sheet metal panels. Looking for guidance that…

Shop floor

Top answer

Time depends on coating thickness, rust depth, and access. For typical sheet metal panels parts with moderate scale, plan methodical passes rather than a single heavy cut at…

0 found this helpful 1 answer
Answer
Admin 17 Apr · asked in Machines
Answered

Should I choose a siphon blast cabinet to remove rust on motorcycle frames in a small shop?

Comparing equipment options for shop work on motorcycle frames. Typical jobs need about 9 hours of blasting per week with crushed glass at 90 PSI. Looking for guidance…

Machines

Top answer

A siphon blast cabinet is a practical fit when weekly volume is around 9 hours and parts are mostly motorcycle frames. Match the pot or cabinet size to…

0 found this helpful 1 answer
Answer
Admin 17 Apr · asked in CFM and air
Answered

How much CFM do I need for a #4 (1/4″) nozzle at 80 PSI in a small shop (guide 488)?

Planning air for a contractor pot. Target pressure is 80 PSI with a #4 (1/4") nozzle while I prep for powder coat on farm equipment. Current compressor is…

CFM and air

Top answer

A #4 (1/4") nozzle at 80 PSI typically needs more continuous CFM than intermittent tool ratings suggest. Treat 100 CFM as a starting estimate and size for duty…

0 found this helpful 1 answer
Answer
Admin 16 Apr · asked in Blast media
Answered

What plastic media grit works best to restore castings on trailer frames in a small shop?

I am blasting trailer frames to restore castings. Shop runs about 60 PSI with a #3 (3/16") nozzle. Looking for a practical plastic media starting point that will…

Blast media

Top answer

For trailer frames, start with plastic media around 80 grit when your goal is to restore castings. At roughly 60 PSI, a #3 (3/16") nozzle gives a controllable…

0 found this helpful 1 answer
Answer
Admin 16 Apr · asked in Shop floor
Answered

How do I quote blasting jobs for automotive frames parts more accurately in a small shop (guide 486)?

Jobs mix rust removal and paint strip ahead of paint strip. Using walnut shell in a vacuum blast unit. Looking for a simple estimating framework. Looking for guidance…

Shop floor

Top answer

Break the quote into access, severity, media, and coating prep. automotive frames with heavy layered coatings can take several times longer than light oxidation.Include consumables: walnut shell, nozzles,…

0 found this helpful 1 answer
Answer
Admin 16 Apr · asked in Safety
Answered

How do I reduce silica and dust exposure while I clean weld scale in a small shop (guide 484)?

Jobs involve cast iron that may carry old coatings. Running 100 PSI on a blast room. Want practical controls beyond basic PPE. Looking for guidance that matches Google-friendly,…

Safety

Top answer

Prefer media and methods that limit respirable dust, maintain sealed containment, and use local exhaust on the blast room. Wet or vacuum-assist options help when the work allows.Assume…

0 found this helpful 1 answer
Answer
Admin 16 Apr · asked in Machines
Answered

How do I set up a portable blaster for first-time aluminum castings blasting in a small shop?

New to production blasting. Goal is to create a paint-ready profile, then apply urethane topcoat. Air available is about 20 CFM. Looking for a safe startup checklist. Looking…

Machines

Top answer

Start with clean, dry garnet, a known-good nozzle, and pressure near 90 PSI. Confirm the portable blaster seals, deadman control, and dust collector before loading parts.Blast a scrap…

0 found this helpful 1 answer
Answer
Admin 15 Apr · asked in CFM and air
Answered

What PSI should I run to strip paint on stainless steel without warping thin metal in a small shop?

Thin stainless steel panels warp when I blast hard. Media is aluminum oxide, nozzle is #4 (1/4"). Need a safer pressure window for coating with powder coat. Looking…

CFM and air

Top answer

On thin stainless steel, begin near the low end of 80 PSI and increase only until you strip paint cleanly. Hot spots and long dwell times warp panels…

0 found this helpful 1 answer
Answer
Admin 15 Apr · asked in Blast media
Answered

How many times can I reclaim glass bead when blasting mild steel in a small shop (guide 481)?

Running a reclaim setup on a siphon blast cabinet. Media is glass bead for remove rust. Wondering when cutting power drops too far for reliable prep. Looking for…

Blast media

Top answer

Reclaim glass bead while particle edges still cut. For mild steel work aimed at remove rust, expect useful life of several cycles if you keep dust and oil…

0 found this helpful 1 answer
Answer
Admin 15 Apr · asked in Shop floor
Answered

What is the most common mistake when learning to prep for powder coat in a small shop (guide 480)?

Training new operators on structural beams. Equipment is a contractor pot, media copper slag. Want a short checklist that prevents rework before clear coat. Looking for guidance that…

Shop floor

Top answer

The most common mistake is dwelling too long in one spot at high pressure. That dishes soft structural beams areas and creates an uneven profile for clear coat.Second…

0 found this helpful 1 answer
Answer
Admin 15 Apr · asked in Safety
Answered

Is it safe to sandblast in a garage with only a steel-toe boots in a small shop (guide 478)?

Hobby blasting on exhaust manifolds parts. Media is soda. Garage has a door fan but no dedicated dust booth. Sessions last about 10 hours. Looking for guidance that…

Safety

Top answer

A garage fan plus a steel-toe boots is not enough for repeated soda blasting. Fine dust settles on tools, cars, and lungs long after the visible cloud clears.Use…

0 found this helpful 1 answer
Answer
Admin 14 Apr · asked in Machines
Answered

Why does my wet blast system keep clogging when I use crushed glass in a small shop (guide 477)?

Frequent stoppages while blasting engine blocks. Media is crushed glass, moisture is sometimes visible in the line, pressure target 90 PSI. Looking for guidance that matches Google-friendly, clear…

Machines

Top answer

Clogs with crushed glass almost always trace to moisture, fines, or an orifice mismatch. Dry the air, screen the media, and verify the metering valve is set for…

0 found this helpful 1 answer
Answer
Admin 14 Apr · asked in CFM and air
Answered

Why does my blast pressure drop below 80 PSI after a few minutes in a small shop (guide 476)?

Pot holds pressure at rest, then falls once I pull the trigger on alloy wheels. Setup uses a #4 (1/4") nozzle and a compressor advertised at 25 CFM.…

CFM and air

Top answer

Pressure collapse after a few minutes usually means the compressor cannot sustain the nozzle demand. A #4 (1/4") at working pressure often exceeds a 25 CFM intermittent rating.Check…

0 found this helpful 1 answer
Answer
Admin 14 Apr · asked in Blast media
Answered

Is plastic media better than garnet for cleaning brake drums before urethane topcoat in a small shop?

Comparing abrasives for brake drums prep ahead of urethane topcoat. Compressor delivers about 20 CFM. Want a finish that accepts primer without heavy sanding. Looking for guidance that…

Blast media

Top answer

Plastic Media and garnet can both prep brake drums, but they leave different profiles. Plastic Media at about 80 grit is a solid first choice when you need…

0 found this helpful 1 answer
Answer
Admin 14 Apr · asked in Shop floor
Answered

How long does it take to strip paint on a typical welded fabrications part in a small shop?

Estimating labor for shop quoting. Setup is a pressure blast pot with walnut shell at 120 PSI. Parts vary but are mostly welded fabrications. Looking for guidance that…

Shop floor

Top answer

Time depends on coating thickness, rust depth, and access. For typical welded fabrications parts with moderate scale, plan methodical passes rather than a single heavy cut at 120…

0 found this helpful 1 answer
Answer
Admin 13 Apr · asked in Machines
Answered

Should I choose a dual-chamber cabinet to restore castings on wrought iron in a small shop?

Comparing equipment options for shop work on wrought iron. Typical jobs need about 3 hours of blasting per week with garnet at 90 PSI. Looking for guidance that…

Machines

Top answer

A dual-chamber cabinet is a practical fit when weekly volume is around 3 hours and parts are mostly wrought iron. Match the pot or cabinet size to your…

0 found this helpful 1 answer
Answer
Admin 13 Apr · asked in CFM and air
Answered

How much CFM do I need for a #4 (1/4″) nozzle at 80 PSI in a small shop (guide 470)?

Planning air for a vacuum blast unit. Target pressure is 80 PSI with a #4 (1/4") nozzle while I peen for fatigue life on steel tanks. Current compressor…

CFM and air

Top answer

A #4 (1/4") nozzle at 80 PSI typically needs more continuous CFM than intermittent tool ratings suggest. Treat 50 CFM as a starting estimate and size for duty…

0 found this helpful 1 answer
Answer
Admin 13 Apr · asked in Blast media
Answered

What glass bead grit works best to debur edges on motorcycle frames in a small shop?

I am blasting motorcycle frames to debur edges. Shop runs about 60 PSI with a #3 (3/16") nozzle. Looking for a practical glass bead starting point that will…

Blast media

Top answer

For motorcycle frames, start with glass bead around 16 grit when your goal is to debur edges. At roughly 60 PSI, a #3 (3/16") nozzle gives a controllable…

0 found this helpful 1 answer
Answer
Admin 12 Apr · asked in Shop floor
Answered

How do I quote blasting jobs for farm equipment parts more accurately in a small shop (guide 468)?

Jobs mix rust removal and paint strip ahead of zinc-rich primer. Using copper slag in a blast room. Looking for a simple estimating framework. Looking for guidance that…

Shop floor

Top answer

Break the quote into access, severity, media, and coating prep. farm equipment with heavy layered coatings can take several times longer than light oxidation.Include consumables: copper slag, nozzles,…

0 found this helpful 1 answer
Answer
Admin 12 Apr · asked in Safety
Answered

How do I reduce silica and dust exposure while I strip paint in a small shop (guide 466)?

Jobs involve automotive frames that may carry old coatings. Running 100 PSI on a pressure blast pot. Want practical controls beyond basic PPE. Looking for guidance that matches…

Safety

Top answer

Prefer media and methods that limit respirable dust, maintain sealed containment, and use local exhaust on the pressure blast pot. Wet or vacuum-assist options help when the work…

0 found this helpful 1 answer
Answer
Post